New Tech Agro Industries

Function : For washing of Amla fruit.

Brief spec :There will be two shallow deep tank mounted on a structure.

·        Comprised of 2 Nos. perforated/Wire mesh baskets in each tank.

·        Manual water sprays arrangement.

·        In 1st tank washing is carried out with help of pressurized blower which is integral part of washer.

·        In 2nd tank it is used for fresh water spraying manually & draining the surface water on the fruits.

·        Complete with necessary fittings like drain valve, Water inlet, etc.

·        M.O.C:- All contact parts SS. 304

·        Elec.Power:1HP/3Phs./ 50 Hrtz./415V.

Function : For blanching of Amla fruits upto 90 deg.

Brief spec : Rectangular thick gauge of 2mm thick tank, perforated/grilled false bottom.

·        Electrical heaters mounting arrangement with safety cover at bottom.

·        Water sealed top covers with handles.

·        Complete with Drain valve, over flow connection, water inlet etc.

·        75mmthickglass wool insulation to prevent heat loss.

·        4 no’s of perforated baskets with handles.

·        Angle section bottom Support structure

·        Digital temperature indicator and controller with control panel.

·        M.O.C.:wettedpartsSS304.

·        Holding Capacity:approx.25Kgbatch

·        Elec. Power:-18kw/single phase.

• Function : For visual inspection and manual separation of Amla seeds after breaking.
• Construction:
• Belt supporting trough thro-out length of top side
• Belt support on return side by PVC rollers and cleaning wiper
• Square Section tubular rigid structure.
• Feed hopper, discharge chute, Motorshroud, chain guard setc.
• 200 mm wide Side table with 2Nos. waste disposal chutes on both sides of conveyor to transfer wastage seeds to below waste collection bins.
• Fixed speed chain drive for bottom conveyor.
• Motor–Hindustan/equivalent Make, Gear box : Bonfiglioli / equivalent make.

Machine Function : For Punching of Amla

Amla punching die and positive forward movement.

Complete with Motor gearbox. Up down cam arrangement.

Feed and discharge hoppers.

Construction : GMP Model with all internal parts quality and all external visible, non-contact parts either made of or covered with M.S. Electrically heated.

·        Double Wall Construction, Inner Chamber Made Of Stainless Steel 304 Quality 18Swg.

·        Thick With Mirror Finish Buffing & Outer Chamber Made Of Mild Steel 18 Swg. Thick With Epoxy Coat Painting.

·        The Oven Will Be Insulated With 100 Mm Thick Glass wool Insulation All Sides Of The Dryer

·        Design Of Panels Will Be Such That Inner & Outer Wall Contact Minimum To Minimize Heat Losses through Conduction.

·        Double Walled Door In Two Parts At Front Side Will Be Provided With Silicon Rubber Gasket, Heavy Duty Male-Female Type Hinges& Ball Catch Locking System.

·        Side Runners Will Be Provided For Resting Trays Inside The Dryer.

Coaxial fan driven by 0.5 HP/1440 RPM/ motor through Bearings & Belt Driven Fan 1 No for Uniform Temperature through out the Dryer.

Quality Tubular Air Heaters on Both Sides. Heaters Mounting Brackets Will Also of S.S.304 Quality Fresh Air Inlet:

Fresh Air Inlet With Filter Provided At Side Of The Tray Dryer.

Safety Controller Will Be Provided. If In Case Main Digital Controller Fails, Safety Controller Will Control The Set Temperature.

Heaters & Blowers Are Interlinked. Heaters Will Not Switch On Unless Motors Are In “On”Position.

Overload Relay Provided For Motor Starter.

MCB Provided For Mains.

Limit Switch Will Be Provided On Front Door, When Doors Open It Will Cuts Off Supply Of Motor& Heaters.

·        Inbuilt Digital Timer, Range 0 To 999 Minutes With Alarm Will Be Provided With The Unit.

·        MOC : Contact parts SS Non contact parts MS powder coated.

·        All internal and air contact parts like inside wall of chamber, inside wall of door, radiator, recirculation fan, fan shaft, safety grids, exhaust damper, etc. in S.S.

·        All external, visible and non-contact parts like outside wall of chamber, outside wall of door, Hinges, handle, door lock, drive support, drive cover, control panel cover, bottom supports, etc. in MS powder coated.

·        Insulation Glasswool.

·        M.O.C : Tray SS304.Non-contactparts MS

Function : For breaking of boiled Amla fruits into segments.

Brief spec  : Pulper mounted on Square tube rigid structure

Assembly for Amla breaking & segmenting

Feed hopper, Waste discharge chute.

Open tray for discharge of Amla segments.

M.O.C.: Wetted Parts SS304